Re: [PATCH v3 2/3] power: reset: imx-snvs-poweroff: add power off driver for i.mx6

From: Robin Gong
Date: Fri Sep 19 2014 - 01:59:00 EST

Next message: Paolo Bonzini: "Re: [PATCH v2] kvm: Faults which trigger IO release the mmap_sem"
Previous message: Mark yao: "[PATCH v3 5/5] drm/rockchip: Add support for Rockchip Soc EDP"
In reply to: Mark Rutland: "Re: [PATCH v3 2/3] power: reset: imx-snvs-poweroff: add power off driver for i.mx6"
Next in thread: Robin Gong: "[PATCH v3 3/3] ARM: configs: imx_v6_v7_defconfig: add power off driver"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Thu, Sep 18, 2014 at 06:53:16PM +0100, Mark Rutland wrote:
> On Thu, Sep 18, 2014 at 03:21:27AM +0100, Robin Gong wrote:
> > On Wed, Sep 17, 2014 at 06:52:44PM +0100, Mark Rutland wrote:
> > > On Wed, Sep 17, 2014 at 10:57:59AM +0100, Robin Gong wrote:
> > > > This driver register pm_power_off with snvs power off function. If
> > > > your boards NOT use PMIC_ON_REQ to turn on/off external pmic, or use
> > > > other pin to do, please disable the driver in dts, otherwise, your
> > > > pm_power_off maybe overwrote by this driver.
> > > >
> > > > Signed-off-by: Robin Gong <b38343@xxxxxxxxxxxxx>
> > > > ---
> > > > .../bindings/power_supply/imx-snvs-poweroff.txt | 23 +++++++
> > > > drivers/power/reset/Kconfig | 9 +++
> > > > drivers/power/reset/Makefile | 1 +
> > > > drivers/power/reset/imx-snvs-poweroff.c | 66 ++++++++++++++++++++
> > > > 4 files changed, 99 insertions(+)
> > > > create mode 100644 Documentation/devicetree/bindings/power_supply/imx-snvs-poweroff.txt
> > > > create mode 100644 drivers/power/reset/imx-snvs-poweroff.c
> > > >
> > > > diff --git a/Documentation/devicetree/bindings/power_supply/imx-snvs-poweroff.txt b/Documentation/devicetree/bindings/power_supply/imx-snvs-poweroff.txt
> > > > new file mode 100644
> > > > index 0000000..6caf64e
> > > > --- /dev/null
> > > > +++ b/Documentation/devicetree/bindings/power_supply/imx-snvs-poweroff.txt
> > > > @@ -0,0 +1,23 @@
> > > > +i.mx6 Poweroff Driver
> > > > +
> > > > +SNVS_LPCR in SNVS module can power off the whole system by pull
> > > > +PMIC_ON_REQ low if PMIC_ON_REQ is connected with external PMIC.
> > > > +If you don't want to use PMIC_ON_REQ as power on/off control,
> > > > +please set status='disabled' to disable this driver.
> > > > +
> > > > +Required Properties:
> > > > +-compatible: "fsl,sec-v4.0-poweroff"
> > > > +-reg: Specifies the physical address of the SNVS_LPCR register
> > >
> > > As you describe above, this is part of the SNVS module. So why does this
> > > need a separate node?
> > >
> > > Surely there should just be a property on the SNVS node that desribers
> > > whether or not this can be used?
> > >
> > > Mark.
> > >
> > Yes, put this function in rtc-snvs make things easier, honestly,this is our way
> > in internal tree. But looks more and more power off driver put in drivers/power
> > /reset,so we decided to add new power off driver. If it is ok to register
> > pm_power_off hook in drivers/rtc/rtc-snvs.c, I can drop this patch.
>
> My view would be that the ability to power off the system is a feature
> of some SNVS modules, and that the SNVS_LPCR register is not a
> sufficiently large sub-block to be described separately. I am not a fan
> of partitioning HW to match Linux implementation details rather than its
> logical structure.
No, actually snvs cover the SNVS_LPCR register. This patch only want to put
pm_power_off under drivers/power/reset instead of drivers/rtc. I'll create
another straightfoward snvs-patch to try, thanks.

>
> So, asuming the layout of the SNS block is well-defined I'd just expect
> a top-level SNVS node, with a driver that can decompose the block
> appropriately and portion it out to different drivers as necessary.
>
> I am not familiar with the hardware, so perhaps that is not a good idea.
> How variable is the SNVS block?
>
> Mark.
>
> > > > +
> > > > +Example:
> > > > + snvs@020cc000 {
> > > > + compatible = "fsl,sec-v4.0-mon", "simple-bus";
> > > > + #address-cells = <1>;
> > > > + #size-cells = <1>;
> > > > + ranges = <0 0x020cc000 0x4000>;
> > > > + .....
> > > > + snvs-poweroff@38 {
> > > > + compatible = "fsl,sec-v4.0-poweroff";
> > > > + reg = <0x38 0x4>;
> > > > + };
> > > > + }
> > > > diff --git a/drivers/power/reset/Kconfig b/drivers/power/reset/Kconfig
> > > > index ca41523..b26c547 100644
> > > > --- a/drivers/power/reset/Kconfig
> > > > +++ b/drivers/power/reset/Kconfig
> > > > @@ -45,6 +45,15 @@ config POWER_RESET_HISI
> > > > help
> > > > Reboot support for Hisilicon boards.
> > > >
> > > > +config POWER_RESET_IMX
> > > > + bool "IMX6 power-off driver"
> > > > + depends on POWER_RESET && SOC_IMX6
> > > > + help
> > > > + This driver support power off external PMIC by PMIC_ON_REQ on i.mx6
> > > > + boards.If you want to use other pin to control external power,please
> > > > + say N here or disable in dts to make sure pm_power_off never be
> > > > + overwrote wrongly by this driver.
> > > > +
> > > > config POWER_RESET_MSM
> > > > bool "Qualcomm MSM power-off driver"
> > > > depends on POWER_RESET && ARCH_QCOM
> > > > diff --git a/drivers/power/reset/Makefile b/drivers/power/reset/Makefile
> > > > index a42e70e..2524daf 100644
> > > > --- a/drivers/power/reset/Makefile
> > > > +++ b/drivers/power/reset/Makefile
> > > > @@ -3,6 +3,7 @@ obj-$(CONFIG_POWER_RESET_AXXIA) += axxia-reset.o
> > > > obj-$(CONFIG_POWER_RESET_BRCMSTB) += brcmstb-reboot.o
> > > > obj-$(CONFIG_POWER_RESET_GPIO) += gpio-poweroff.o
> > > > obj-$(CONFIG_POWER_RESET_HISI) += hisi-reboot.o
> > > > +obj-$(CONFIG_POWER_RESET_IMX) += imx-snvs-poweroff.o
> > > > obj-$(CONFIG_POWER_RESET_MSM) += msm-poweroff.o
> > > > obj-$(CONFIG_POWER_RESET_QNAP) += qnap-poweroff.o
> > > > obj-$(CONFIG_POWER_RESET_RESTART) += restart-poweroff.o
> > > > diff --git a/drivers/power/reset/imx-snvs-poweroff.c b/drivers/power/reset/imx-snvs-poweroff.c
> > > > new file mode 100644
> > > > index 0000000..d726ac4
> > > > --- /dev/null
> > > > +++ b/drivers/power/reset/imx-snvs-poweroff.c
> > > > @@ -0,0 +1,66 @@
> > > > +/* Power off driver for i.mx6
> > > > + * Copyright (c) 2014, FREESCALE CORPORATION. All rights reserved.
> > > > + *
> > > > + * based on msm-poweroff.c
> > > > + *
> > > > + * This program is free software; you can redistribute it and/or modify
> > > > + * it under the terms of the GNU General Public License version 2 and
> > > > + * only version 2 as published by the Free Software Foundation.
> > > > + *
> > > > + * This program is distributed in the hope that it will be useful,
> > > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > > > + * GNU General Public License for more details.
> > > > + *
> > > > + */
> > > > +
> > > > +#include <linux/err.h>
> > > > +#include <linux/init.h>
> > > > +#include <linux/io.h>
> > > > +#include <linux/kernel.h>
> > > > +#include <linux/module.h>
> > > > +#include <linux/of.h>
> > > > +#include <linux/of_address.h>
> > > > +#include <linux/platform_device.h>
> > > > +
> > > > +static void __iomem *snvs_base;
> > > > +
> > > > +static void do_imx_poweroff(void)
> > > > +{
> > > > + u32 value = readl(snvs_base);
> > > > +
> > > > + /* set TOP and DP_EN bit */
> > > > + writel(value | 0x60, snvs_base);
> > > > +}
> > > > +
> > > > +static int imx_poweroff_probe(struct platform_device *pdev)
> > > > +{
> > > > + snvs_base = of_iomap(pdev->dev.of_node, 0);
> > > > + if (!snvs_base) {
> > > > + dev_err(&pdev->dev, "failed to get memory\n");
> > > > + return -EIO;
> > > > + }
> > > > +
> > > > + pm_power_off = do_imx_poweroff;
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static const struct of_device_id of_imx_poweroff_match[] = {
> > > > + { .compatible = "fsl,sec-v4.0-poweroff", },
> > > > + {},
> > > > +};
> > > > +MODULE_DEVICE_TABLE(of, of_imx_poweroff_match);
> > > > +
> > > > +static struct platform_driver imx_poweroff_driver = {
> > > > + .probe = imx_poweroff_probe,
> > > > + .driver = {
> > > > + .name = "imx-snvs-poweroff",
> > > > + .of_match_table = of_match_ptr(of_imx_poweroff_match),
> > > > + },
> > > > +};
> > > > +
> > > > +static int __init imx_poweroff_init(void)
> > > > +{
> > > > + return platform_driver_register(&imx_poweroff_driver);
> > > > +}
> > > > +device_initcall(imx_poweroff_init);
> > > > --
> > > > 1.7.9.5
> > > >
> > > >
> > >
> > > _______________________________________________
> > > linux-arm-kernel mailing list
> > > linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> > > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> >
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Next message: Paolo Bonzini: "Re: [PATCH v2] kvm: Faults which trigger IO release the mmap_sem"
Previous message: Mark yao: "[PATCH v3 5/5] drm/rockchip: Add support for Rockchip Soc EDP"
In reply to: Mark Rutland: "Re: [PATCH v3 2/3] power: reset: imx-snvs-poweroff: add power off driver for i.mx6"
Next in thread: Robin Gong: "[PATCH v3 3/3] ARM: configs: imx_v6_v7_defconfig: add power off driver"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]