Re: [PATCH v2 5/5] ARM: dts: sun50i: h6: Introduce Beelink GS1 board

From: ClÃment PÃron
Date: Fri Apr 05 2019 - 08:52:23 EST

Hi,

Adding this r_pio regulators make a new error in the bootlog :

[ 0.346843] sun50i-h6-r-pinctrl 7022000.pinctrl: Couldn't get bank
PL regulator
[ 0.346853] sun50i-h6-r-pinctrl 7022000.pinctrl: request() failed for pin 352
[ 0.346862] sun50i-h6-r-pinctrl 7022000.pinctrl: pin-352
(7081400.i2c) status -517
[ 0.346871] sun50i-h6-r-pinctrl 7022000.pinctrl: could not request
pin 352 (PL0) from group PL0 on device 7022000.pinctrl
[ 0.346878] mv64xxx_i2c 7081400.i2c: Error applying setting,
reverse things back

PL0 and PL1 are SCK/SDA for the PMIC :(

Clement

On Fri, 5 Apr 2019 at 14:21, ClÃment PÃron <peron.clem@xxxxxxxxx> wrote:
>
> Beelink GS1 is an Allwinner H6 based TV box,
> which support:
> - Allwinner H6 Quad-core 64-bit ARM Cortex-A53
> - GPU Mali-T720
> - 2GB LPDDR3 RAM
> - AXP805 PMIC
> - 1Gbps GMAC via RTL8211E
> - FN-Link 6222B-SRB Wifi/BT
> - 1x USB 2.0 Host and 1x USB 3.0 Host
> - HDMI port
> - S/PDIF Tx
> - IR receiver
> - 5V/2A DC power supply
>
> Signed-off-by: ClÃment PÃron <peron.clem@xxxxxxxxx>
> ---
>
> Thanks to Jagan and Icenowy, most of this devicetree is taken from their works on
> the OrangePi One Plus and Pine H64.
>
> Changes in v2 (Thanks to Maxime Ripard):
> - move MMC pinctrl to SOC dtsi
> - add board to Sunxi YAML file
> - add PIO/R_PIO regulators
> - remove always_on from SDIO regulators
>
>
> .../devicetree/bindings/arm/sunxi.yaml | 5 +
> arch/arm64/boot/dts/allwinner/Makefile | 1 +
> .../dts/allwinner/sun50i-h6-beelink-gs1.dts | 256 ++++++++++++++++++
> 3 files changed, 262 insertions(+)
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
>
> diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml
> index 11563d3f7c65..9ab9b266881d 100644
> --- a/Documentation/devicetree/bindings/arm/sunxi.yaml
> +++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
> @@ -136,6 +136,11 @@ properties:
> - const: lemaker,bananapro
> - const: allwinner,sun7i-a20
>
> + - description: Beelink GS1
> + items:
> + - const: azw,beelink-gs1
> + - const: allwinner,sun50i-h6
> +
> - description: Beelink X2
> items:
> - const: roofull,beelink-x2
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> index e4dce2f6fa3a..2dd806a3d5c9 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-beelink-gs1.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-lite2.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
> new file mode 100644
> index 000000000000..d820a138522b
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
> @@ -0,0 +1,256 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +/*
> + * Copyright (C) 2019 ClÃment PÃron <peron.clem@xxxxxxxxx>
> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-h6.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + model = "Beelink GS1";
> + compatible = "azw,beelink-gs1", "allwinner,sun50i-h6";
> +
> + aliases {
> + ethernet0 = &emac;
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + connector {
> + compatible = "hdmi-connector";
> + type = "a";
> +
> + port {
> + hdmi_con_in: endpoint {
> + remote-endpoint = <&hdmi_out_con>;
> + };
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + power {
> + label = "beelink:white:power";
> + gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
> + default-state = "on";
> + };
> + };
> +
> + reg_vcc5v: vcc5v {
> + /* board wide 5V supply directly from the DC jack */
> + compatible = "regulator-fixed";
> + regulator-name = "vcc-5v";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +};
> +
> +&de {
> + status = "okay";
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&emac {
> + pinctrl-names = "default";
> + pinctrl-0 = <&ext_rgmii_pins>;
> + phy-mode = "rgmii";
> + phy-handle = <&ext_rgmii_phy>;
> + phy-supply = <&reg_aldo2>;
> + allwinner,rx-delay-ps = <0>;
> + allwinner,tx-delay-ps = <0>;
> + status = "okay";
> +};
> +
> +&hdmi {
> + status = "okay";
> +};
> +
> +&hdmi_out {
> + hdmi_out_con: endpoint {
> + remote-endpoint = <&hdmi_con_in>;
> + };
> +};
> +
> +&mdio {
> + ext_rgmii_phy: ethernet-phy@1 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
> + };
> +};
> +
> +&mmc0 {
> + vmmc-supply = <&reg_cldo1>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
> + bus-width = <4>;
> + status = "okay";
> +};
> +
> +&mmc2 {
> + vmmc-supply = <&reg_cldo1>;
> + vqmmc-supply = <&reg_bldo2>;
> + non-removable;
> + cap-mmc-hw-reset;
> + bus-width = <8>;
> + status = "okay";
> +};
> +
> +&ohci0 {
> + status = "okay";
> +};
> +
> +&pio {
> + vcc-pd-supply = <&reg_cldo1>;
> + vcc-pg-supply = <&reg_aldo1>;
> +};
> +
> +&r_i2c {
> + status = "okay";
> +
> + axp805: pmic@36 {
> + compatible = "x-powers,axp805", "x-powers,axp806";
> + reg = <0x36>;
> + interrupt-parent = <&r_intc>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + x-powers,self-working-mode;
> + vina-supply = <&reg_vcc5v>;
> + vinb-supply = <&reg_vcc5v>;
> + vinc-supply = <&reg_vcc5v>;
> + vind-supply = <&reg_vcc5v>;
> + vine-supply = <&reg_vcc5v>;
> + aldoin-supply = <&reg_vcc5v>;
> + bldoin-supply = <&reg_vcc5v>;
> + cldoin-supply = <&reg_vcc5v>;
> +
> + regulators {
> + reg_aldo1: aldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-pl";
> + };
> +
> + reg_aldo2: aldo2 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-ac200";
> + regulator-enable-ramp-delay = <100000>;
> + };
> +
> + reg_aldo3: aldo3 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc25-dram";
> + };
> +
> + reg_bldo1: bldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-bias-pll";
> + };
> +
> + reg_bldo2: bldo2 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-efuse-pcie-hdmi-io";
> + };
> +
> + reg_bldo3: bldo3 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-dcxoio";
> + };
> +
> + bldo4 {
> + /* unused */
> + };
> +
> + reg_cldo1: cldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-3v3";
> + };
> +
> + reg_cldo2: cldo2 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-wifi-1";
> + };
> +
> + reg_cldo3: cldo3 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-wifi-2";
> + };
> +
> + reg_dcdca: dcdca {
> + regulator-always-on;
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1080000>;
> + regulator-name = "vdd-cpu";
> + };
> +
> + reg_dcdcc: dcdcc {
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1080000>;
> + regulator-name = "vdd-gpu";
> + };
> +
> + reg_dcdcd: dcdcd {
> + regulator-always-on;
> + regulator-min-microvolt = <960000>;
> + regulator-max-microvolt = <960000>;
> + regulator-name = "vdd-sys";
> + };
> +
> + reg_dcdce: dcdce {
> + regulator-always-on;
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-name = "vcc-dram";
> + };
> +
> + sw {
> + /* unused */
> + };
> + };
> + };
> +};
> +
> +&r_pio {
> + vcc-pl-supply = <&reg_aldo1>;
> + vcc-pm-supply = <&reg_aldo1>;
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_ph_pins>;
> + status = "okay";
> +};
> +
> +&usb2otg {
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usb2phy {
> + usb0_vbus-supply = <&reg_vcc5v>;
> + status = "okay";
> +};
> --
> 2.17.1
>